Basic Info.
Suitable for
Recycled Material, Wood, Paper
Paper Thickness
Normal Specification Paper
Economic Speed
60-80m/Min
Corrugated Paper
100-200G/M2
The Highest Pressure
1.2MPa
Equipment Covers
About38m*10m*5m
Transport Package
Plastic
Specification
WJ100-1800-I
Product Description
main technical parameters and requirements in production line- The maximum production width of the corrugated cardboard:1800mm
- Design speed:100m/min
- Economic speed:60-80m/min
note:Production line speed test paper should meet the following requirements:(the surface temperature of the equipment is not less than 172ºC) Paper rating of not less than B grade Paper moisture content of about:11%±2% top paper:100-250g/m2 core paper:100--250g/m2 corrugated paper:100-200g/m2 4.Flute-type combination:A ,C, B, E(as customers' requirement)
5.Steam the necessary requirements:
amount of steam 2500-3000Kg/Hr the highest pressure:1.2MPa common pressure:0.8-1.1MPa 6,power supply:380V 50Hz Three-phase four-wire system 7,equipment installed total power:about120Kw The actual power consumption:about 60Kw(full speed) 8,equipment covers:about38m×10m×5m(Specific length of foundation Figure prevail) 9,Equipment out of paper orientation:According to the user to determine the transmission plant set left or right position 10,Equipment applicability,Available in A, B, C class domestic or imported paper PaperCustomer-owned section1,steam heating system:proposal with 2000Kg / Hr of a steam boiler pressure:1.25MPa steam pipeline.2,air compressed machine,air pipeline,glue conveying pipe.3,power supply,wires connected to the operation panel and line pipe.4,water sources,water pipelines,buckets and so on.5,Water, electricity, gas flush mounting civil foundation.6,Test with the base paper,corn starch (potato),Industrial use caustic soda,borax and other material.7,Oil equipment,lubricating oil,hydraulic oil,lubricating grease.8,installation,commissioning of food, accommodation.And provide installers with the installation.ZJ-F shaftless mill roll standStructural features:★Symmetrical structure can also install two bundles of paper at the same time,Paper can be used for non-stop for a job;Adopts mechanical drive to complete the paper clamping, lifting, loosen, move on, around translational motion, etc.★each shaftless mill roll stand is equipped with two pieces of paper guide, two set of paper car;paper guide the use of channel 14 and the guide post weld,paper car adopt 10mmwelded stell,the length of track is 4500mm.★manual dics brake,add screw following★electric elements centralized control the electric elements,expand chuck.technical parameters:1,Backstands action mode:mechanical electric operation2,the range of paper jams:maximum:1800mm minimum:600mm3,the diameter of paper jams:maximum:¢1400mm minimum:¢400mm4,Unilateral maximum load:maximum2000Kg5,Powered motor parameters:Paper jams motor550W×4set 380V 50HZ short(S2)working standardlift motor 1.5Kw 380V 50HZ short(S2)working standardSF-280S fingerless type single facerStructural features:★Adopt vacuum suction structure, with high pressure strong blower.Suction with silencer.Gas supply and electrical control cabinet to focus on the same operation cabinet,not less than 1.5 meters away from the host,Fully enclosed full operation side.★base and wallboard cast iron wall,Wallboard thickness130mm.universal Joints.★corrugated roller material adopt 48CrMoalloy steel,quenched,Laser hardening,Surface finish,main roll of corrugated diameter¢ 280mm,surface hardnessHRC60degree above.The key parts of the tile and pressure roller bearings Wafangdian produce high temperature bearings.★pressure roller ¢ 284mm,surface grinding and chrome-plated;cylinder control and remove up and down, 45 carbon steel materials, quenching (with cushioning devices).★pneumatic control glue to glue back, glue roller diameter ¢215mm,Engraved polished surface after a 36-line pit style textured machined chrome plated,after scraping the roller surface polished hard chrome plated.★Corrugated roller, pressure roller materials provided by the Central Plains Steel,High on corrugating unilateral 0.15mm, 0.075mm high pressure roller unilateral. Plus stopper. ¢ 160mm cylinder with compression cylinder.★preheat roll adopt seamless steel pipe production by tiangang ¢ 300mm,connecting with metal Hose.regular technical parameters:1,effective width:1800mm 2,operation direction:left or right(determined in accordance with customer plant)3,design speed:100m/min 4,temperature range:200-260ºC5,corrugated flute:(UV type or UVV type)roller diameters parameters:1,diameter of corrugated roller: ¢280mm 2,diameter of pressure roller: ¢284mm3,diameter of glue roller: ¢216mm 4,diameter of preheat roller: ¢320mmpowered motor parameters:1,main drive motor:7.5Kw rated voltage:380V 50Hz Continuous (S1) working standard2,suction motor:7.5Kw rated voltage:380V 50Hz Continuous (S1) working standardRG-2-600 triple preheater Structural features:★preheat roller accord with the national standard of the pressure vessal,and enclosed the pressure container certificate and inspection certificate.★Each roller surface after grinding precision grinding and dealing with hard chrome plating, Surface friction is small, durable.★electric adjustable angle, it can rotated adjust the paper preheat area in the range of 360°.technical parameters:1,diameter of preheat roller:¢600mm range of angle adjustment:360°rotation diameter of wrap angle axis:¢85mm2,steam temperature:150-200ºC steam pressure:0.8-1.3MPa3,motor power:250W short(S2)working system 380V 50HzGM-12 double glue machineStructural features:★After the glue roller surface after quenching inner hole machining, grinding and dynamic balancing surface engraved with pit style textured, coating evenly, less consumption of plastic.★doctor roller surface by grinding and hard chromium plating.★other guide rollers with hard chrome plated.★Pressure roller with pneumatic lift, easy operation.★ manually adjust scraping gap.★glue roller ¢ 215mm,Doctor roll¢ 122mm,press paper roller¢ 122mm,preheat roller 270mm.★Electrical design, construction production process, follow the national standards, low failure rate, easy maintenance.regular technical parameters:1,MAX.working width:1800mm 2,operation direction:left or right(Determined in accordance with the customer's facility)3,design speed:100m/min 4,Gas supply system:0.4-0.6Mpa5,Preheat cylinder temperature range:150-200ºC Steam pressure:0.8-1.2MpaRoller diameter parameters:1,glue roller diameter:¢215mm doctor roller diameter:¢122mm2,lower preheating roll diameter:¢270mm under preheat roller diameter:¢270mm3, Over the paper roll diameter:¢85mmPower motors and electrical parameters:1,glue roller initiative frequency motor:3KW 380V 50Hz Continuous (S1) working standard2,glue pump motor: 2.2KW 380V 50Hz Continuous (S1)working systemSM-10 type double facerStructural features:★Heating plate surface by grinding treatment, hot plate width 600mm, a total of 12 heating plate and cooling 4 m. Heating plate with a container board production, in line with national standards for a class pressure vessel, with pressure vessel certificate and inspection certificate.★Hot plate with intensive gravitational roll structure. Roll adopt pneumatic lifting.★Heating plate heat transfer pipe temperature control sub-four-segment, with a temperature display.★on cotton use two-cylinder S type cotton belt with the tensioning device.★lower belt adopt pneumatic tensioning.★Drive roller coated with attached wear-resistant rubber ,showed a herringbone structure,With a high, ensure smooth cardboard output.★Main drive motor for frequency conversion motor,low-speed torque,wide speed range ,reliable, and easy maintenance.★hot plate internal for partition isolation structure,s-shaped flow of steam,Steam, water separation function significantly improves the utilization of steam.technical parameters:1,temperature requirement:160-200ºC steam pressure:0.8-1.3MPa 2,air source pressure:0.6-0.9MPa3,Cooling stereotypes length:4m Heating plate quantity:9 pieces 4,hydraulic system pressure:6---8MParoller diameter parameters:1,upper drive rubber roller diameter:¢475mm lower drive rubber roller diameter : ¢350mm Wear rubber Outsourcing2,Former follower with roller diameter:¢215mm back setting belt driven roller diameter:¢176mm3,Platen roller: ¢70mm Setting roller diameter:¢86mm4,upper belt tension roller diameter:¢155mm upper roll diameter with detuning:¢124mm5, Entrusted with the roll diameter lower belt:¢130mmNote: All the roller surface after grinding are hard chrome plated.ZQS thin knife slittingstructural feature:★Overcome the conventional type of pole, cutting pressure lines appear when collapsed cardboard cut phenomenon, cutting board smooth, quality has improved significantly.★the whole machine can remove left and right,cycloid reducer to adjust.★Cutter and easy to adjust the pressure line, the error ± 0.5mm, automatic sharpening device, you can achieve timing Brothers, with intermittent Brothers and other features.★the machine adopt five knives eight lines,the blade is made of tungsten alloy steel, the using life is not less than 3 million running meters.regular technical parameters:1,effective width:1800mm
2,The maximum mechanical speed:100m/min3,Mechanical configuration: 5knives 8lines
4,The minimum width of the cutter:135mm 5.The maximum width of the cutter:1850mmDMT-120 paper sheet delivery and side conveyorstructural features: ★Adopted on the 16th channel welded.Electric adjustment of cardboard the size of the lateral output pneumatic control board, electrically adjustable conveyor speed.★Cardboard sheets to the desired number or height requirements will be controlled by a foot switch out of cardboard.★Vertical bin using wide flat belt conveyor transport.technical parameters:1.The maximum accumulation length:3000mm 2,The maximum stack height:200mmPower motors and electrical parameters:1.Main conveyor motor:3Kw adopt frequency motor 2,Lateral output of the motor:1.5Kw Three-phase asynchronous motor3,Walking Motor:1.5Kw Three-phase asynchronous motorZJZ glue station systemStructural features:★provide the starch adhesive to the corrugated single facer ,two glue machine and some other gluing equipment.★Horizontal glue machine can meanwhile matched with main body glue and carrier glue, and mixing, glue large.★Making room storage barrels adhesive solution was to use the glue pump rubber equipment storage barrels, adhesive solution for equipment.★Storage barrels, plastic barrels with mixing device, avoid glue solution precipitation agglomerate.★System unit with carrier vessel, main tank, storage tank, and send the glue pump, the back glue pump, etc.★glue system adopt glue cycle,rest glue go back to the glue square cylinder,Liquid level float automatic control,the back glue a bucket of glue liquid being beaten back with glue equipment storage bucket,cycle for glue,Save the glue solution,prevent the glue solution in the rubber plate pasting and caking precipitation.★Work has been completed, the residual gum dividend total pipeline with rubber equipment rubber pumped back rubber room storage barrels, for next time use.★Responsible for technical guidance, teaching adhesive dispensing process.
Address:
Development Zone, East of Dongguang County, Cangzhou, Hebei, China
Business Type:
Manufacturer/Factory
Business Range:
Industrial Equipment & Components, Manufacturing & Processing Machinery, Packaging & Printing
Management System Certification:
ISO 9001
Company Introduction:
HRB-PACK GROUP Co., Ltd.
Since 1999. Located in the south of Beijing and north of Jinan, 3 factories in China for Corrugated cardboard production line, Flexo printer slotter die cutter machine, Flute laminator machine. We have independent export and import company, can export to clients directly.
We have more than 30, 000 sqm production plant, and 3, 000 sqm office building. More than 400 staffs, include sales team, after sales teams, production team, scientific research team...
We have after-sale office in China, Vietnam, India, Bangladesh, Italy…
With a large quantity of models and complete specifications, our products can meet the demand of different clients. With the spirit of keeping improving, we pursue perfection constantly. Our company actively carries out the overall quality managing work. Because of the beautiful and tasteful appearance, compact and careful technology, reasonable price and perfect after-sale service, our products have won the trust and praise from clients all over the country for many years.
Regarding vigorously developing the carton industry in China as our task, we′ll sincerely cooperate with clients and meet their demands with better quality products and perfect after-sale services.
